Fulton Hogan Industries Pty Ltd

Site

Pavement and Materials Engineering – Binders Laboratory

Accreditation No.

3321

Site No.

3314

Date of Accreditation

07 Jan 1992

Address

25 Groves Avenue
Mcgraths Hill, NSW 2756
Australia

fultonhogan.com.au

Contact

Mr Khoa Vo P: +61 0448096252

Availability

Services conditionally available to external clients

Fulton Hogan Industries Pty Ltd address map

Scope of Accreditation

Print scopes
Pavement and Materials Engineering – Binders Laboratory

ISO/IEC 17025 (2017)

Infrastructure and Asset Integrity

Service Product Determinant Technique Procedure Limitations
Evaluation of geotechnical and civil construction material - Aggregate binder adhesion Aggregates Resistance to stripping Plate test

AS 1141.50

TfNSW TS 02799.27
Initial adhesion Not applicable

TfNSW TS 02799.35

ISO/IEC 17025 (2017)

Materials

Service Product Determinant Technique Procedure Limitations
Analysis of bituminous materials - Composition Bituminous materials Recovery of residue Not applicable

AS/NZS 2341.30
Toluene insoluble matter Not applicable

AS/NZS 2341.8
Rubber content Not applicable TfNSW TS 02808.08
Water content Dean and Stark

AS 2341.9
Non-aqueous volatiles Calculation by difference

AS/NZS 2341.24
Residue on evaporation Not applicable

AS/NZS 2341.23
Analysis of bituminous materials - Properties Bituminous materials Stress ratio Dynamic shear rheometer  Austroads Method AGPT/T125
Particle charge Not applicable

AS/NZS 2341.22
Rolling thin film oven (RTFO) Effect of heat and air on a moving film of bitumen

AS/NZS 2341.10, Austroads ATM 103
Softening point Ring and ball

AS 2341.18 and Austroads method AGPT/T131
Durability Accelerated aging viscosity increase Austroads Method AGPT/T194
Consistency of bitumen emulsion Derived Engler calculation

AS 2341.25
Sedimentation Not applicable

AS/NZS 2341.27
Sample recovery Solvent extraction Austroads Method AGPT/T191
Sieve residue Sieve analysis

AS/NZS 2341.26
Viscosity Dynamic - Capillary tube

AS/NZS 2341.2
Penetration of bitumen Not applicable

AS 2341.12
Permanent recovery and creep Dynamic shear rheometer AASHTO Method T350
Classification of slurry surfacing materials Schulze-Breuer and Ruck ISSA TB-144
pH of bituminous emulsions Classical AS 2341.32
Stone coating ability and water resistance Not applicable

AS 2341.28
Abrasion loss Wet track abrasion Austroads Method AGPT/T272
Consistency; Stiffness Not applicable In-house Method FHMS 04
Sample handling and conditioning Not applicable

AS/NZS 2341.21, Austroads ATM 102
Viscosity Dynamic shear rheometer  Austroads Method ATM 192, Austroads Method AGPT/T193, AASHTO Method T315
Segregation of bituminous materials Not applicable

Austroads method AGPT/T108 
Excess binder Loaded wheel Austroads Method AGPT/T273
Density Density bottle

AS 2341.7
Flash point of polymer modified binder Not applicable

Austroads ATM 112
Breaking behaviour Setting time

AS 2341.29
Flash point of cutback bitumen Not applicable

AS 2341.16
Flash point Not applicable AS 2341.14
Viscosity Rotational viscometer

Austroads ATM 111
Torsional recovery Not applicable

Austroads ATM 122
Cutback bitumen composition Distillation

AS 2341.15
Consistency; Elastic recovery; Stiffness Not applicable

Austroads method ATM 121
Set and cure of bituminous slurry Cohesion Austroads Method AGPT/T271
Compressive limit Not applicable

Austroads ATM 132
Homogeneity of liquid pre-coats and adhesion agents Not applicable

TfNSW TS 02805.01
Aggregate coating Visual examination ISSA TB114
Viscosity Rotational

AS/NZS 2341.4
Sample collection Bituminous materials Not applicable Residual bitumens from tanks, tankers and drums

AS 2008
Not applicable Bitumen emulsions from tanks, tankers and drums

AS 1160 Appendix A
Not applicable Polymer modified bitumens from tanks, tankers and drums

Austroads ATM 101

The only data displayed is that deemed relevant and necessary for the clear description of the Activities and Services covered by the Scope of Accreditation (SoA).

Grey text appearing in a SoA is additional freetext providing further refinement or information on the data in the preceding line entry.

The Product column may also describe an Item or Material.

The Limitations column may also describe the Range.