S G Prittie Precision Gauges Pty Ltd

Site

S G Prittie Precision Gauges Pty Ltd

S G Prittie Calibration Services Pty Ltd

Accreditation No.

419

Site No.

412

Date of Accreditation

10 May 1963

Address

21 King Street
Airport West, VIC 3042
Australia

prittie.com.au

Contact

Mr Jim Gordon P: +61 (03) 83788888

Availability

Services available to external clients

Scope of Accreditation

S G Prittie Precision Gauges Pty Ltd

ISO/IEC 17025 (2017)

Calibration

  • The uncertainty of measurement is reported as an expanded uncertainty having a level of confidence of 95% unless stated otherwise
Service Product Determinant Technique Procedure Limitations
Dimensional metrology - Engineering equipment and precision instruments Depth and height micrometers; External micrometers; Internal micrometers; Micrometer heads Length measurements Comparison with a reference standard

Micrometer heads

Including compliance with AS 2328

External micrometers

Including compliance with AS 2102, BS 870, JIS B7502

Internal micrometers

Including compliance with AS 2102, BS 959, JIS B7502

Depth micrometers

Including compliance with BS 6468, JIS B7544

Capability

with Calibration and Measurement Capability of -

Micrometers heads
2.0 µm from 1mm to 50mm
External micrometers
2.0 µm from 25mm to 100mm
3.0 µm above 100mm to 400mm
4.8 µm above 400mm to 700mm
6.7 µm above 700mm to 1000mm
Internal micrometers
2.0 µm from 5.0 up to 100 mm
3.6 µm above 100 mm up to 300mm
5.5 µm above 300 mm up to 600mm
8.0 µm above 600 mm up to 1000mm
depth micrometers
2.0 µm up to 25 mm
2.6 µm above 25 to 100mm
4.0 µm above 100 mm up to 300mm
7.0 µm above 300 mm up to 750mm


Dial gauges Length measurements Comparison with a reference standard

Including compliance with AS 2103, BS 907 and BS 2795

Capability

with Calibration and Measurement Capability of -

(including Dial gauges, digital indicators and electronic indicators)
1.0 µm up to 50 mm range
Electronic calipers; Electronic height and depth gauges; Vernier calipers; Vernier height and depth gauges Length measurements Comparison with a reference standard

Electronic and vernier callipers

Including compliance with AS 1984, BS 887,and JIS B7507

Electronic and vernier height and depth gauges

Including compliance with AS 1643, JIS B7517 and JIS B7518 

Capability

with Calibration and Measurement Capability of -

Electronic and vernier callipers

10 µm up to 300mm
13 µm above 300mm up to 600mm
20 µm above 600mm up to 1000mm

Electronic and vernier height and depth gauges

10 μm from 150 mm to 1000 mm

Dimensional metrology - Jigs, fixtures, cutting tools, machine tools, gears, splines and serrations Components and QC standards; Cutting tools; Jigs and fixtures; Position and receiver gauges Angle; Form; Length measurements Direct measurement Reference connectors only
Including compliance with: -
ISO 594-2:1998 Fig. 5 / ISO 80369-7 Fig. C.1 Female reference Luer lock connector for testing male Luer connector
ISO 594-2:1998 Fig. 6 / ISO 80369-7 Fig. C.3 Female reference connector for testing male Luer lock connector
ISO 594-2:1998 Fig. 7 / ISO 80369-7 Fig. C.4 Male reference Luer lock connector for testing female Luer connector
ISO 594-2:1998 Fig. 8 / ISO 80369-7 Fig. C.6 Male reference connector for testing female Luer lock connector
ISO 594-1:1986 Fig. 5 / ISO 80369-7 Fig. C.2 Male reference Luer slip connector for testing female Luer connector
ISO 594-1:1986 Fig. 4 / ISO 80369-7 Fig. C.5 Female reference Luer slip connector for testing male Luer connector
ISO 80369-3 Fig. C.1 Female reference connector for testing male Enteral connector
ISO 80369-3 Fig. C.2 Female reference connector for testing male Enteral connector
ISO 80369-3 Fig. C.3 Male reference connector for testing female Enteral connector
ISO 80369-3 Fig. C.4 Male reference connector for testing female Enteral connector
ISO 80369-6 Fig. C.1 Female reference lock connector for testing male Neuraxial connector
ISO 80369-6 Fig. C.2 Male reference slip connector for testing female Neuraxial connector
ISO 80369-6 Fig. C.3 Female reference connector for testing male Neuraxial connector
ISO 80369-6 Fig. C.4 Male reference lock connector for testing female Neuraxial connector
ISO 80369-6 Fig. C.5 Male reference connector for testing female Neuraxial lock connector
ISO 18250-8 Fig. C.1 Male Apheresis AC Reservoir Reference Connector
ISO 18250-8 Fig. C.2 (assembly of C.3 and C.4) Female Apheresis AC Reservoir Reference Connector
ISO 18250-8 Fig. C.5 Male Apheresis AC Reservoir Reference Connector
ISO 18250-8 Fig. C.6 (assembly of C.7 and C.8) Female Apheresis AC Reservoir reference Connector
ISO80369-2 Fig C.1 female reference connector for testing male RESP-125 connectors (R1)
ISO80369-2 Fig C.2 female reference connector for testing male RESP-125 connectors (R1)
ISO80369-2 Fig C.3 (assembly of C.5 & C.6) male reference connector for testing female RESP-125 connectors (R1)
ISO80369-2 Fig C.4 (assembly of C.5 & C.7) male reference connector for testing female RESP-125 connectors (R1)
ISO80369-2 Fig C.8 female reference lock connector for testing male RESP-6000 connectors (R2)
ISO80369-2 Fig C.9 female reference connector for testing male RESP-6000 connectors (R2)
ISO80369-2 Fig C.10 (assembly of C.12 & C.13) male reference lock connector for testing female RESP-6000 connectors (R2)
ISO80369-2 Fig C.11 (assembly of C.12 & C.14) male reference connector for testing female RESP-6000 connectors (R2)
ISO 18250-3 Fig C.1 Cross port reference reservoir connector for testing cross connector (E1R)
ISO 18250-3 Fig C.2 Cross port reservoir reference connector for testing cross connector (E1R)
ISO 18250-3 Fig C.3 Cross reference connector for testing cross port reservoir connector (E1R)
ISO 18250-3 Fig C.4 Cross reference connector for testing cross port reservoir connector (E1R)
ISO 18250-3 Fig C.5 Male reference connector for testing female enteral reservoir connector (E2R)
ISO 18250-3 Fig C.6 Female reference connector for testing male enteral reservoir connector (E2R)          

Capability

with Calibration and Measurement Capability of -

(2.5+L/333) µm up to 1100mm where L is in mm

Reference connectors
Determinants: Diameter, taper, length, thread flank angle, form, pitch, lead, width of flat, radii
with Calibration and Measurement Capability of -
taper cone diameter 1.6 µm
lengths 3.0 µm
flank angle 0.05°
thread diameters 3.0 µm
pitch, lead, 5.0 µm
width of flat 5.0µm
Dimensional metrology - Length and angle standards External cylindrical standards Angle (arc); Length measurements Comparison with a reference standard

Capability

with Calibration and Measurement Capability of -

0.5 μm from 1 mm to 25 mm

0.8 μm above 25 mm to 50 mm

1.0 μm above 50 mm to 100 mm

1.7 µm above 100 mm to 200 mm
2.5 µm above 200 mm to 300 mm
Dimensional metrology - Limit gauges and reference standards Adjustable thread caliper gauges Flank angle; Length measurements; Major diameter and simple pitch diameter; Minor diameter and simple pitch diameter; Thread form Comparison with a reference standard

Capability

Major diameter, simple pitch diameter, pitch, thread form and angle

with Calibration and Measurement Capability of -

6 μm from 2 mm to 100 mm

10 μm from 100 mm to 200 mm

12 μm from 200 mm to 300 mm

Concentricity gauges; Depth gauges; Indicator gauges; Step gauges Diameter; Length measurements Comparison with a reference standard

Capability

with Calibration and Measurement Capability of -

2.0 µm up to 50 mm
3.0 µm above 50 mm up to 150 mm
5.0 µm above 150 mm up to 300 mm
External length
5 μm from 300 mm to 1000 mm


Parallel screw plug gauges Flank angle; Length measurements; Major diameter and simple pitch diameter; Minor diameter and simple pitch diameter; Thread form Comparison with a reference standard

Capability

Major diameter, simple pitch diameter, pitch, thread form and angle

with Calibration and Measurement Capability of -

2.5 μm from 2 mm to 25 mm

3 μm above 25 mm to 100 mm

4.5 μm above 100 mm to 200 mm

6 μm above 200 mm to 300 mm

Parallel screw ring gauges Flank angle; Length measurements; Major diameter and simple pitch diameter; Minor diameter and simple pitch diameter; Thread form Comparison with a reference standard

Capability

Major diameter, simple pitch diameter, pitch, thread form and angle

with Calibration and Measurement Capability of -

3.5 μm from 2 mm to 50 mm

5 μm from 50 mm to 100 mm

6.5 μm from 100 mm to 200 mm

8 μm from 200 mm to 300 mm

Plain gap gauges Length measurements Comparison with a reference standard

Capability

with Calibration and Measurement Capability of -

2 μm from 2 mm to 50 mm
3 μm above 50 mm to 150 mm
5 μm above 150 mm to 300 mm
7.5 µm above 300 mm to 500 mm


Plain plug gauges Diameter Comparison with a reference standard

Capability

with Calibration and Measurement Capability of -

0.5 μm from 0.2 mm to 25 mm
0.8 μm above 25 mm to 50 mm
1.0 μm above 50 mm to 100 mm
2.0 μm above 100 mm to 200 mm
2.5 µm above 200 mm to 300 mm

Spheres
0.8 µm from 1 mm to 25 mm
1.7 µm above 25 mm to 50 mm
2.6 µm above 50 mm to 150 mm
Plain ring gauges Diameter Comparison with a reference standard

Capability

with Calibration and Measurement Capability of -

5 μm from 0.5 mm to 1.7 mm
1.5 μm above 1.7 mm to 50 mm
3 μm above 50 mm to 180 mm
4 μm above  180 mm to 240 mm
5 μm above 240 mm to 300 mm


Profile gauges Flank angle; Length measurements Comparison with a reference standard

Capability

with Calibration and Measurement Capability of -

10 μm from 1 mm to 150 mm

Taper plug gauges Diameter; Length measurements Comparison with a reference standard

Capability

with Calibration and Measurement Capability of -

1.6 µm from 1.0 mm to 20 mm.
2.0 µm above 20 mm to 50 mm
3.5 µm above 50 mm to 150 mm
4.0 µm above 150 mm to 300 mm

Taper ring gauges Diameter; Length measurements Comparison with a reference standard

Capability

with Calibration and Measurement Capability of -

1.6 µm from 1.0 mm to 20 mm
2.0 µm above 20 mm to 50 mm
4.0 µm above 50 mm to 150 mm
6.0 µm above 150 mm to 250 mm

Taper screw plug gauges Flank angle; Length measurements; Major diameter and simple pitch diameter; Minor diameter and simple pitch diameter; Taper; Thread form Comparison with a reference standard

Capability

Major diameter, simple pitch diameter, pitch, thread form and angle

with Calibration and Measurement Capability of -

Tapers from 1 in 500 to 1 in 8

5 μm from 2 mm to 50 mm

6 μm above 50 mm to 100 mm

7 μm above 100 mm to 200 mm

8 μm above 200 mm to 300 mm

Taper screw ring gauges Flank angle; Length measurements; Major diameter and simple pitch diameter; Minor diameter and simple pitch diameter; Taper; Thread form Comparison with a reference standard

Capability

Major diameter, simple pitch diameter, pitch, thread form and angle

with Calibration and Measurement Capability of -

Tapers from 1 in 500 to 1 in 8

5.0 µm from 2 mm to 100 mm
8.0 µm above 100 mm to 165 mm

Dimensional metrology - Surface topography Components and QC standards Roundness Comparison with a reference standard by differential measurement

Evaluation of roundness to BS 3730

Capability

with Calibration and Measurement Capability of -

0.25 μm from 3 mm to 300 mm diameter

The only data displayed is that deemed relevant and necessary for the clear description of the activities and services covered by the scope of accreditation.

Grey text appearing in a SoA is additional freetext providing further refinement or information on the data in the preceding line entry.