SRG Global Asset Care Pty Ltd

Site

Sydney NDT and Mechanical Testing Services

Accreditation No.

218

Site No.

1086

Date of Accreditation

20 Nov 1973

Address

Unit 2b, 149 McCredie Road
Smithfield, NSW 2164
Australia

srgglobal.com.au

Contact

Mr Ivan Lo P: +61 (02) 87863100

Availability

Services available to external clients

SRG Global Asset Care Pty Ltd address map

Scope of Accreditation

Print scopes
Sydney NDT and Mechanical Testing Services

ISO/IEC 17025 (2017)

Infrastructure and Asset Integrity

Service Product Determinant Technique Procedure Limitations
Evaluation of load handling, rigging and tensioning systems Anchorages and supports for industrial fall arrest systems Proof load Not applicable

AS 1891.4

in-house procedure MT-PRD.008

up to 100 kN

Chain Breaking load; Proof load Not applicable AS 2321
 1 to 1000 kN
Lifting clutches for concrete elements Breaking load; Proof load Not applicable  AS 3850.1 clause 2.6 1 to 1000 kN
Plate clamps and gripping devices Breaking load; Proof load Not applicable AS 4991 1 to 1000 kN
Rigging screws and turnbuckles Breaking load; Proof load Not applicable AS 2319
 1 to 1000 kN
Shackles Breaking load; Proof load Not applicable AS 2741
 1 to 1000 kN
Non-destructive testing (NDT) - Electromagnetic testing Metallic surfaces Defect detection and characterisation High frequency eddy current
Non-destructive testing (NDT) - Electromagnetic testing - Specialised - Magnetic flux leakage (MFL) Metallic plate Profiling Not applicable Above ground storage tanks
Non-destructive testing (NDT) - Magnetic particle testing Metallic surfaces - Magnetic Defect detection and characterisation AC magnetic flow; Coil; Current flow Current flow: DC up to 1500A
Coil: DC up to 1500A
Non-destructive testing (NDT) - Penetrant testing Metallic surfaces Defect detection and characterisation Solvent removable; Water washable
Non-destructive testing (NDT) - Radiographic testing Castings - Cast irons, steel and alloy steels; Castings - Non-ferrous metals and alloys; Composite materials; Welded joints - Aluminium alloys; Welded joints - Clad and overlaid steel; Welded joints - Copper and copper-nickel alloys; Welded joints - Ferritic materials; Welded joints - Stainless steel, austenitic and duplex materials; Welded joints - Titanium and titanium alloys Defect detection and characterisation Film radiography

Metallic piping; Metallic tubes - Ferromagnetic materials; Metallic tubes - Non-ferromagnetic materials Material profiling; Wall thickness Film radiography
Non-destructive testing (NDT) - Ultrasonic testing Bonded metals; Castings - Cast irons, steel and alloy steels; Machine bearings; Rolled or wrought aluminium products; Rolled or wrought steel products; Welded joints - Aluminium alloys; Welded joints - Ferritic materials; Welded joints - Stainless steel, austenitic and duplex materials Defect detection and characterisation A-scan - Manual Bonded materials includes welded hard facings, friction welded components
Castings; Forgings; Metallic components; Metallic piping; Metallic plate; Metallic tubes - Non-ferromagnetic materials Material thickness - Spot/grid only A-scan - Manual; Thickness meter
Castings; Forgings; Metallic components; Metallic piping; Metallic tubes - Ferromagnetic materials; Metallic tubes - Non-ferromagnetic materials Material loss characterisation; Profiling A-scan - Manual
Non-destructive testing (NDT) - Visual testing - Prior to initial service Castings; Forgings; Rolled products; Welded joints Defect detection Visual testing

ISO/IEC 17025 (2017)

Manufactured Goods

Service Product Determinant Technique Procedure Limitations
Evaluation of access protection products Access covers; Grates; Inspection covers Load Not applicable

AS 3996 Appendix C

 up to 1000 kN
Material performance evaluation of elastomers, plastics and composite products Prepared test specimens Tensile properties Tensile tests with load stress and cross-head control

ISO 13953
in-house procedure MT.ENG.009

Crushing decohesion Not applicable ISO 13955
Peel decohesion Not applicable ISO 13954
Material performance evaluation of metal products Fixtures and components Strength of assembly; Tensile properties Tensile tests with load stress and cross-head control in-house procedure MT.ENG.009 1 to 1000 kN 
Prepared metallic test specimens Hardness Vickers

AS 1817.1

ASTM E92
ISO 6507-1

9.8 N to 294 N

Shear strength Not applicable ISO 15630-2 for compliance with AS/NZS 1554.3 Table 4.7.5
 1 to 1000 kN
Tensile properties Axial tensile; Longitudinal tensile; Tensile tests with control of strain rate, including yield stress and proof stress; Transverse tensile; Uniaxial tension

AS 1391
ASTM A370, ASTM A770/770M, ASTM B557, ASTM E8/E8M
ISO 6892.1
DNV GL Rules for classification; Lloyds Rules for manufacture, testing and certification of materials

1 to 1000 kN

Bending properties Longitudinal bend; Reverse bend; Simple bend; Supported mandrel bend; Transverse free bend; V block bend

AS 2505.1, .2, .3, .4
ASTM A370, ASTM E290
ISO 7438
Lloyds Rules for manufacture, testing and certification of materials Chapter 2 Section 7

Hardness Brinell - Portable tester ASTM E110

Tests at 29.4 kN

Hardness Brinell

AS 1816.1

ASTM A370, ASTM E 10
ISO 6506-1

4.9 to 29.4 kN

Charpy impact toughness Charpy - Assessment of fracture appearance; Charpy U-notch - Impact value; Charpy V-notch - Impact value

AS 1544.2, .3, .5
ISO 148-1
DNV GL Rules for classification Part 2: Materials and welding part 2 Chapter 1 Section 3
Lloyds Rules for the manufacture, testing and certification of materials Chapter 2 Section 3.

from 80°C to -70°C and at -196°C

Hardness Rockwell

AS 1815.1

ASTM A370, ASTM E18

ISO 6508-1
 Rockwell scales B and C
Reinforcing bar and steel prestressing materials for concrete Bending properties Longitudinal guided bend; Re-bend; Reverse bend AS/NZS 4671 Section 7.2.3
ISO 15630-1, ISO 15630-2
Shear strength of welded joints in mesh Direct shear force AS/NZS 4671 Section 7.2.5
ISO 15630-1, ISO 15630-2
Geometric properties Surface geometry AS/NZS 4671 Section 7.4
ISO 15630-1, ISO 15630-2
Tensile properties Longitudinal tensile; Tensile tests with control of strain rate, including yield stress and proof stress; Uniform elongation (Agt)

AS/NZS 4671  Section 7.2.2

ISO 15630-1, ISO 15630-2
 1 to 1000 kN
Geometric properties Mass per unit length AS/NZS 4671 Appendix C3.3
ISO 15630-1, ISO 15630-2
Threaded fasteners, bolts and nuts Breaking load Not applicable

AS/NZS 1252.1 Sections 2.4 and 3.4, AS 4291.1 Sections 9.1, 9.2, 9.4, 9.5, 9.7 

ASTM A370, ASTM F606/F606M

ISO 898-1, ISO 3506-1 (excluding Section 7.2.3), ISO 6892-1

1 to 1000 kN

Proof load Not applicable

AS/NZS 1252.1 Sections 2.4 and 3.4

AS/NZS 4291.1 Section 9.6

AS/NZS 4291.2

ASTM F606/F606M 

ISO 898-1, 898-2, ISO 3506-2

1 to 1000 kN

Tubing/piping Flattening properties Not applicable

ASTM A370

Twistlocks Permanent set; Proof load; Shear strength; Tensile properties Not applicable BS 5237
in-house procedure MT.ENG.009
AS 3711.10 Annex B7.1
AS 3711.10 Annex B7.3		 1 to 1000 kN
Welded test specimens Fracture test Visual examination

AS 1796, AS 1665, AS/NZS 2205.4.1, AS 2980
AS/NZS 3992
AWS D 1.1 Section 4/AWS B4.0,
ASME IX QW-180, QW-182, QW-462
ISO 9017, ISO 9606.1,.2,.3
DNV GL Rules for classification, Lloyds Rules for manufacture, testing and certification of materials

Charpy impact toughness Charpy - Assessment of fracture appearance; Charpy U-notch - Impact value; Charpy V-notch - Impact value

AS 1544.2; .3, .5, AS 2205.7.1

AS/NZS 3992, AS/NZS 1554.1, .4, .5

ISO 148-1, ISO 9016

DNV GL Rules for classification of ships/ high speed, light craft and naval surface craft part 2 Chapter 3 Section 5

Lloyds Rules for the manufacture, testing and certification of materials Chapter 12

from 80°C to -70°C and at -196°C

Hardness Brinell

AS 1816.1, ASTM A370, ASTM E 10
ISO 6506-1

Tensile properties Longitudinal tensile; Tensile tests with control of strain rate, including yield stress and proof stress; Transverse butt tensile; Transverse joggle-butt tensile

AS 1391, AS 1665, AS 1697, AS 2205.2.1, 2.2, .2.3, AS 2885.2
AS/NZS 1554.1, .2, .3, .4, .5, .6, AS/NZS 3992
ASTM A370, ASTM E8/ E8M,
ISO 4136, ISO 5178, ISO 6892.1, ISO 15614 -1, 2, 6
ASME IX QW-150/QW-462/QB 451
AWS D1.1 Section 4/AWS B4.0,
API 5L, API 650
DNV GL Rules for classification, Lloyds Rules for manufacture, testing and certification of materials

1 to 1000 kN

Bending properties Longitudinal guided bend; Transverse free bend; Transverse guided bend; Transverse joggle-butt wrap around bend

AS 1665, AS 1697, AS 1796, AS 2205.3.1, .3.2, .3.3, .3.4, AS 2885.2, AS 2980
AS/NZS 1554.1, .2, .3, .4, .5, .6, AS/NZS 3992
ASME IX QW-160, QW-462, QB 160, QB-466
AWS D 1.1 Section 4/AWS B4.0
ASTM E190
API 650
ISO 5173, ISO 9606.1, .2, .3
DNV GL Rules for classification, Lloyds Rules for manufacture, testing and certification of materials

Hardness Vickers

AS 1817.1, AS 2205.6.1
AS/NZS 1554.1, .4, .5, AS/NZS 3992
ASTM E92
ISO 6507-1, ISO 9015-1, ISO 15614-1
APL 5L, API 650
ANSI/AWS D1.1 Section 4, AWS B4.0


 in the range 9.8 N to 294 N
Hardness Rockwell

AS 1815.1
AS/NZS 1554.1, .4, .5, AS/NZS 3992
ASTM A370, ASTM E18
ISO 15614-1
APL 5L, API 650
ANSI/AWS D1.1 Section 4, AWS B4.0

 Rockwell scales B and C
Macroscopic examination Macroscopic examination

AS 1796, AS 1665, AS/NZS 2205.5.1, AS 2980
AS/NZS 3992, ISO 17639,
AWS D 1.1 Section 4/AWS B4.0,
ASME IX QW-183, QW-184, QW-462
ISO 9017, ISO 9606.1,.2,.3
DNV GL Rules for classification, Lloyds Rules for manufacture, testing and certification of materials

Shear strength Not applicable ISO 15630-2 for compliance with AS/NZS 1554.3 Table 4.7.5
 1 to 1000 kN
Mechanical performance evaluation of ladders, racks, scaffolds and supports Scaffolding and scaffolding components Deflection; Load carrying capacity Not applicable

AS/NZS 1577 Appendices A, B
AS 1576.2 Appendices A to N incl.

ISO/IEC 17025 (2017)

Materials

Service Product Determinant Technique Procedure Limitations
Metallic corrosion evaluation Austenitic, duplex and nickel-chromium alloys Detrimental intermetallic phase Ferric chloride corrosion test ASTM A923 Method C
Austenitic, duplex and nickel-chromium alloys; Chemical corrosion treatment materials Pitting corrosion resistance Critical crevice temperature; Critical pitting temperature; Ferric chloride crevice; Ferric chloride pitting

ASTM G48

Austenitic, duplex and nickel-chromium alloys; Ferrous materials Intergranular corrosion resistance Acidified copper sulfate exposure - Mony-Penny-Strauss; Copper-copper sulfate-sulfuric acid; Ferric sulfate - Sulfuric acid; Nitric acid exposure - Huey; Oxalic acid etch

AS 2038-1997 Section 7

ASTM A262 Practice E

ASTM A763 Practice Z		 Ferrous materials including ferritic stainless steels
Copper and copper alloys Dezincification resistance Not applicable

AS 2345

ISO 6509-1
Plating Coating thickness Microscopic examination

AS 2331.1.1

Coating thickness Dissolution - Strip, weigh and analytical

 AS 2331.2.1, AS 4534 Appendix E2

ASTM B767

ISO 10111

Metallographic evaluation of metals and alloys Aluminium and aluminium alloys Grain size Comparison method; Intercept (Heyn) method; Microscopic examination

 AS 1733

ASTM E112

Anodising thickness Microscopic examination

AS 2331.1.1

ISO 1463
Depth of surface defects Microscopic examination

ISO 6157-1, -2, -3

Depth of cladding Microscopic examination

 AS 2331.1.1

Phase identification and proportion Microscopic examination; Point count ASTM E562
Aluminium and aluminium alloys Exfoliation corrosion susceptibility; Macroscopic examination Visual examination

 ASTM G66

Copper and copper alloys Grain size Comparison method; Intercept (Heyn) method; Microscopic examination

 AS 1733

ASTM E112

Phase identification and proportion Microscopic examination ASTM E562
Ferrous materials Degree of spheroidisation Not applicable ISO 945-1
Case depth and depth of decarburisation Hardness traverse; Macroscopic examination; Microhardness; Microscopic examination

AS 1982, AS 2003, AS 4291.1

Non-metallic inclusion content Macroscopic examination; Microscopic examination

AS 2197

ASTM E45 Section 6
Phase identification and proportion Microscopic examination; Point count

 ASTM E562

 including proportion of ferrite in austenitic steels
Macroscopic examination Macroscopic examination AS 2087
ASTM E45 Section 5
Graphite type and distribution in cast irons Microscopic examination

AS 1830, AS 1831 

ASTM A247

ISO 945-1
Depth of surface defects Microscopic examination

AS/NZS 4291.1
ISO 6157-1, -2, -3

Grain size Comparison method; Intercept (Heyn) method; Microscopic examination

 AS 1733

ASTM E112, ASTM E1181

Magnesium alloys Depth of surface defects Microscopic examination

ISO 6157-1, -2, -3

Phase identification and proportion Microscopic examination; Point count ASTM E562
Grain size Comparison method; Intercept (Heyn) method; Microscopic examination

 AS 1733

ASTM E112

Nickel and nickel alloys Depth of surface defects Microscopic examination

ISO 6157-1, -2, -3

Grain size Comparison method; Intercept (Heyn) method; Microscopic examination AS 1733
ASTM E112
Phase identification and proportion Microscopic examination; Point count ASTM E562
Titanium and titanium alloys Depth of surface defects Microscopic examination

ISO 6157-1, -2, -3

Grain size Comparison method; Intercept (Heyn) method; Microscopic examination AS 1733
ASTM E112
Phase identification and proportion Microscopic examination; Point count ASTM E562

The only data displayed is that deemed relevant and necessary for the clear description of the activities and services covered by the scope of accreditation.

Grey text appearing in a SoA is additional freetext providing further refinement or information on the data in the preceding line entry.