Fuel Calibration Services Pty Ltd

Site

Fuel Calibration Services Pty Ltd

Accreditation No.

19101

Site No.

21542

Date of Accreditation

24 Dec 2012

Address

26 McKinnon Road
Pinelands, NT 829
Australia

fcsnt.com.au

Contact

Mr James Malcom Ritchie P: +61 (08) 89474700

Availability

Services available to external clients

Fuel Calibration Services Pty Ltd address map

Scope of Accreditation

Print scopes
Fuel Calibration Services Pty Ltd

ISO/IEC 17025 (2017)

Calibration

  • The uncertainty of measurement is reported as an expanded uncertainty having a level of confidence of 95% unless stated otherwise
Service Product Determinant Technique Procedure Limitations
Flow metrology - Flow measuring devices and systemsincluding on site calibrations Liquid meters Volume (and nominal flow rate) Direct comparison against a reference standard

Including stating compliance with the specifications in the National Measurement Institute Test Procedure NITP 5.1 & 5.2

Capability

Including on site calibrations

Calibration of flow meters for water and liquid hydrocarbons other than LPG

with Calibration and Measurement Capability of -

0.1% of volume with a minimum 20 L test volume by the volumetric method using a reference volume measure

0.1% of volume with a minimum 200 L test volume by the volumetric method using a master meter

at flow rates in the range 6 L/min to 3800 L/min
Pressure metrology - Pressure and vacuum measuring equipment Digital pressure gauges; Mechanical pressure gauges; Pressure recorders; Vacuum gauges Gauge pressure By pressure calibrator; Comparison with dead weight tester MSA Test Method 1 for digital gauges
MSA Test Method 2 for mechanical gauges 

Capability

with Calibration and Measurement Capability of -

0.06% of reading or 0.2 kPa (whichever is greater) from -95 kPa to 2000 kPa (pneumatic measurement)

0.06% of reading or 0.5 kPa (whichever is greater) from 100 kPa to 280 MPa (hydraulic measurement)

0.06% of reading or 0.5 kPa (whichever is greater) from 100 kPa to 60 MPa (oil-free hydraulic measurement)

Torque - Torque measuring and testing equipment Torque wrenches Torque Comparison with a reference standard

including compliance with BS EN ISO 6789

Capability

with Calibration and Measurement Capability of-

1.0 % of reading from 0.5 Nm to 1500 Nm

ISO/IEC 17025 (2017)

Infrastructure and Asset Integrity

Service Product Determinant Technique Procedure Limitations
Evaluation of mechanical performance of pressure equipment Hose and hose assemblies; Piping; Pressure fittings; Valves Conductivity; Hydrostatic pressure Not applicable AS 1180.5:1999 Sections 7.1, 7.2,
AS 1180.13A:1987 kinds 1 and 2 only,
AS 1180.13B:1987 kinds 1 and 2 only,
AS 1180.13C and AS 2683 Appendix C,
AS 1271 Section 2.6 and 3.6 (a) to (e), 3.6.2 (except lift and discharge capacity),
AS 2117 Sections 2.1, 2.2, 2.6.1, 2.6.2,
AS 2683 Sections 2.1, 2.5,
AS 2792 Section 3.1.2 and Appendix E up to 105 MPa,
AS 4037 Sections 17, 19,
AS 4041 Sections 6.6, 6.7		 up to 280 MPa
Valves Pneumatic pressure Not applicable AS 1271 Section 3.4 and 3.5 Up to 280 MPa

The only data displayed is that deemed relevant and necessary for the clear description of the activities and services covered by the scope of accreditation.

Grey text appearing in a SoA is additional freetext providing further refinement or information on the data in the preceding line entry.