National Association of Testing Authorities, Australia
Scope of Accreditation
SRG Global Asset Care Pty Ltd
Site
Sydney NDT and Mechanical Testing Services
Accreditation No.
218
Site No.
1086
Date of Accreditation
20 Nov 1973
Contact
Availability
Services available to external clients
Scope of Accreditation
ISO/IEC 17025 (2017)
Infrastructure and Asset Integrity
Service | Product | Determinant | Technique | Procedure | Limitations |
---|---|---|---|---|---|
Evaluation of load handling, rigging and tensioning systems | Anchorages and supports for industrial fall arrest systems | Proof load | Not applicable | AS 1891.4 in-house procedure MT-PRD.008 | up to 100 kN |
Chain | Breaking load; Proof load | Not applicable | AS 2321 | 1 to 1000 kN | |
Lifting clutches for concrete elements | Breaking load; Proof load | Not applicable | AS 3850.1 clause 2.6 | 1 to 1000 kN | |
Plate clamps and gripping devices | Breaking load; Proof load | Not applicable | AS 4991 | 1 to 1000 kN | |
Rigging screws and turnbuckles | Breaking load; Proof load | Not applicable | AS 2319 | 1 to 1000 kN | |
Shackles | Breaking load; Proof load | Not applicable | AS 2741 | 1 to 1000 kN | |
Non-destructive testing (NDT) - Electromagnetic testing | Metallic surfaces | Defect detection and characterisation | High frequency eddy current | ||
Non-destructive testing (NDT) - Electromagnetic testing - Specialised - Magnetic flux leakage (MFL) | Metallic plate | Profiling | Not applicable | Above ground storage tanks | |
Non-destructive testing (NDT) - Magnetic particle testing | Metallic surfaces - Magnetic | Defect detection and characterisation | AC magnetic flow; Coil; Current flow | Current flow: DC up to 1500A Coil: DC up to 1500A | |
Non-destructive testing (NDT) - Penetrant testing | Metallic surfaces | Defect detection and characterisation | Solvent removable; Water washable | ||
Non-destructive testing (NDT) - Radiographic testing | Castings - Cast irons, steel and alloy steels; Castings - Non-ferrous metals and alloys; Composite materials; Welded joints - Aluminium alloys; Welded joints - Clad and overlaid steel; Welded joints - Copper and copper-nickel alloys; Welded joints - Ferritic materials; Welded joints - Stainless steel, austenitic and duplex materials; Welded joints - Titanium and titanium alloys | Defect detection and characterisation | Film radiography | | |
Metallic piping; Metallic tubes - Ferromagnetic materials; Metallic tubes - Non-ferromagnetic materials | Material profiling; Wall thickness | Film radiography | |||
Non-destructive testing (NDT) - Ultrasonic testing | Bonded metals; Castings - Cast irons, steel and alloy steels; Machine bearings; Rolled or wrought aluminium products; Rolled or wrought steel products; Welded joints - Aluminium alloys; Welded joints - Ferritic materials; Welded joints - Stainless steel, austenitic and duplex materials | Defect detection and characterisation | A-scan - Manual | Bonded materials includes welded hard facings, friction welded components | |
Castings; Forgings; Metallic components; Metallic piping; Metallic plate; Metallic tubes - Non-ferromagnetic materials | Material thickness - Spot/grid only | A-scan - Manual; Thickness meter | |||
Castings; Forgings; Metallic components; Metallic piping; Metallic tubes - Ferromagnetic materials; Metallic tubes - Non-ferromagnetic materials | Material loss characterisation; Profiling | A-scan - Manual | |||
Non-destructive testing (NDT) - Visual testing - Prior to initial service | Castings; Forgings; Rolled products; Welded joints | Defect detection | Visual testing |
ISO/IEC 17025 (2017)
Manufactured Goods
Service | Product | Determinant | Technique | Procedure | Limitations |
---|---|---|---|---|---|
Evaluation of access protection products | Access covers; Grates; Inspection covers | Load | Not applicable | AS 3996 Appendix C | up to 1000 kN |
Material performance evaluation of elastomers, plastics and composite products | Prepared test specimens | Tensile properties | Tensile tests with load stress and cross-head control | ISO 13953 | |
Crushing decohesion | Not applicable | ISO 13955 | |||
Peel decohesion | Not applicable | ISO 13954 | |||
Material performance evaluation of metal products | Fixtures and components | Strength of assembly; Tensile properties | Tensile tests with load stress and cross-head control | in-house procedure MT.ENG.009 | 1 to 1000 kN |
Prepared metallic test specimens | Hardness | Vickers | AS 1817.1 ASTM E92ISO 6507-1 | 9.8 N to 294 N | |
Shear strength | Not applicable | ISO 15630-2 for compliance with AS/NZS 1554.3 Table 4.7.5 | 1 to 1000 kN | ||
Tensile properties | Axial tensile; Longitudinal tensile; Tensile tests with control of strain rate, including yield stress and proof stress; Transverse tensile; Uniaxial tension | AS 1391 | 1 to 1000 kN | ||
Bending properties | Longitudinal bend; Reverse bend; Simple bend; Supported mandrel bend; Transverse free bend; V block bend | AS 2505.1, .2, .3, .4 | |||
Hardness | Brinell - Portable tester | ASTM E110 | Tests at 29.4 kN | ||
Hardness | Brinell | AS 1816.1 ASTM A370, ASTM E 10ISO 6506-1 | 4.9 to 29.4 kN | ||
Charpy impact toughness | Charpy - Assessment of fracture appearance; Charpy U-notch - Impact value; Charpy V-notch - Impact value | AS 1544.2, .3, .5 | from 80°C to -70°C and at -196°C | ||
Hardness | Rockwell | AS 1815.1 ASTM A370, ASTM E18 ISO 6508-1 | Rockwell scales B and C | ||
Reinforcing bar and steel prestressing materials for concrete | Bending properties | Longitudinal guided bend; Re-bend; Reverse bend | AS/NZS 4671 Section 7.2.3 ISO 15630-1, ISO 15630-2 | ||
Shear strength of welded joints in mesh | Direct shear force | AS/NZS 4671 Section 7.2.5 ISO 15630-1, ISO 15630-2 | |||
Geometric properties | Surface geometry | AS/NZS 4671 Section 7.4 ISO 15630-1, ISO 15630-2 | |||
Tensile properties | Longitudinal tensile; Tensile tests with control of strain rate, including yield stress and proof stress; Uniform elongation (Agt) | AS/NZS 4671 Section 7.2.2 ISO 15630-1, ISO 15630-2 | 1 to 1000 kN | ||
Geometric properties | Mass per unit length | AS/NZS 4671 Appendix C3.3 ISO 15630-1, ISO 15630-2 | |||
Threaded fasteners, bolts and nuts | Breaking load | Not applicable | AS/NZS 1252.1 Sections 2.4 and 3.4, AS 4291.1 Sections 9.1, 9.2, 9.4, 9.5, 9.7 ASTM A370, ASTM F606/F606M ISO 898-1, ISO 3506-1 (excluding Section 7.2.3), ISO 6892-1 | 1 to 1000 kN | |
Proof load | Not applicable | AS/NZS 1252.1 Sections 2.4 and 3.4 AS/NZS 4291.1 Section 9.6 AS/NZS 4291.2ASTM F606/F606M ISO 898-1, 898-2, ISO 3506-2 | 1 to 1000 kN | ||
Tubing/piping | Flattening properties | Not applicable | ASTM A370 | ||
Twistlocks | Permanent set; Proof load; Shear strength; Tensile properties | Not applicable | BS 5237 in-house procedure MT.ENG.009 AS 3711.10 Annex B7.1 AS 3711.10 Annex B7.3 | 1 to 1000 kN | |
Welded test specimens | Fracture test | Visual examination | AS 1796, AS 1665, AS/NZS 2205.4.1, AS 2980 | ||
Charpy impact toughness | Charpy - Assessment of fracture appearance; Charpy U-notch - Impact value; Charpy V-notch - Impact value | AS 1544.2; .3, .5, AS 2205.7.1 AS/NZS 3992, AS/NZS 1554.1, .4, .5 ISO 148-1, ISO 9016 DNV GL Rules for classification of ships/ high speed, light craft and naval surface craft part 2 Chapter 3 Section 5 Lloyds Rules for the manufacture, testing and certification of materials Chapter 12 | from 80°C to -70°C and at -196°C | ||
Hardness | Brinell | AS 1816.1, ASTM A370, ASTM E 10 | |||
Tensile properties | Longitudinal tensile; Tensile tests with control of strain rate, including yield stress and proof stress; Transverse butt tensile; Transverse joggle-butt tensile | AS 1391, AS 1665, AS 1697, AS 2205.2.1, 2.2, .2.3, AS 2885.2 | 1 to 1000 kN | ||
Bending properties | Longitudinal guided bend; Transverse free bend; Transverse guided bend; Transverse joggle-butt wrap around bend | AS 1665, AS 1697, AS 1796, AS 2205.3.1, .3.2, .3.3, .3.4, AS 2885.2, AS 2980 | |||
Hardness | Vickers | AS 1817.1, AS 2205.6.1 | in the range 9.8 N to 294 N | ||
Hardness | Rockwell | AS 1815.1 | Rockwell scales B and C | ||
Macroscopic examination | Macroscopic examination | AS 1796, AS 1665, AS/NZS 2205.5.1, AS 2980 | |||
Shear strength | Not applicable | ISO 15630-2 for compliance with AS/NZS 1554.3 Table 4.7.5 | 1 to 1000 kN | ||
Mechanical performance evaluation of ladders, racks, scaffolds and supports | Scaffolding and scaffolding components | Deflection; Load carrying capacity | Not applicable | AS/NZS 1577 Appendices A, B |
ISO/IEC 17025 (2017)
Materials
Service | Product | Determinant | Technique | Procedure | Limitations |
---|---|---|---|---|---|
Metallic corrosion evaluation | Austenitic, duplex and nickel-chromium alloys | Detrimental intermetallic phase | Ferric chloride corrosion test | ASTM A923 Method C | |
Austenitic, duplex and nickel-chromium alloys; Chemical corrosion treatment materials | Pitting corrosion resistance | Critical crevice temperature; Critical pitting temperature; Ferric chloride crevice; Ferric chloride pitting | ASTM G48 | ||
Austenitic, duplex and nickel-chromium alloys; Ferrous materials | Intergranular corrosion resistance | Acidified copper sulfate exposure - Mony-Penny-Strauss; Copper-copper sulfate-sulfuric acid; Ferric sulfate - Sulfuric acid; Nitric acid exposure - Huey; Oxalic acid etch | AS 2038 Section 7 ASTM A262 Practice E ASTM A763 Practice Z | Ferrous materials including ferritic stainless steels | |
Copper and copper alloys | Dezincification resistance | Not applicable | AS 2345 ISO 6509-1 | ||
Plating | Coating thickness | Microscopic examination | AS 2331.1.1 | ||
Coating thickness | Dissolution - Strip, weigh and analytical | AS 2331.2.1, AS 4534 Appendix E2 ASTM B767 ISO 10111 | |||
Metallographic evaluation of metals and alloys | Aluminium and aluminium alloys | Grain size | Comparison method; Intercept (Heyn) method; Microscopic examination | AS 1733 ASTM E112 | |
Anodising thickness | Microscopic examination | AS 2331.1.1 ISO 1463 | |||
Depth of surface defects | Microscopic examination | AS/NZS 4291.1 | |||
Depth of cladding | Microscopic examination | AS 2331.1.1 | |||
Phase identification and proportion | Microscopic examination; Point count | ASTM E562 | |||
Aluminium and aluminium alloys | Exfoliation corrosion susceptibility; Macroscopic examination | Visual examination | ASTM G66 | ||
Copper and copper alloys | Grain size | Comparison method; Intercept (Heyn) method; Microscopic examination | AS 1733 ASTM E112 | ||
Phase identification and proportion | Microscopic examination | ASTM E562 | |||
Ferrous materials | Degree of spheroidisation | Not applicable | ISO 945-1 | ||
Case depth and depth of decarburisation | Hardness traverse; Macroscopic examination; Microhardness; Microscopic examination | AS 1982, AS 2003, AS 4291.1 | |||
Non-metallic inclusion content | Macroscopic examination; Microscopic examination | AS 2197 ASTM E45 Section 6 | |||
Phase identification and proportion | Microscopic examination; Point count | ASTM E562 | including proportion of ferrite in austenitic steels | ||
Macroscopic examination | Macroscopic examination | AS 2087 ASTM E45 Section 5 | |||
Graphite type and distribution in cast irons | Microscopic examination | AS 1830, AS 1831 ASTM A247 ISO 945-1 | |||
Depth of surface defects | Microscopic examination | AS/NZS 4291.1 | |||
Grain size | Comparison method; Intercept (Heyn) method; Microscopic examination | AS 1733 ASTM E112, ASTM E1181 | |||
Magnesium alloys | Depth of surface defects | Microscopic examination | AS/NZS 4291.1 | ||
Phase identification and proportion | Microscopic examination; Point count | ASTM E562 | |||
Grain size | Comparison method; Intercept (Heyn) method; Microscopic examination | AS 1733 ASTM E112 | |||
Nickel and nickel alloys | Depth of surface defects | Microscopic examination | AS/NZS 4291.1 | ||
Grain size | Comparison method; Intercept (Heyn) method; Microscopic examination | AS 1733 ASTM E112 | |||
Phase identification and proportion | Microscopic examination; Point count | ASTM E562 | |||
Titanium and titanium alloys | Depth of surface defects | Microscopic examination | AS/NZS 4291.1 | ||
Grain size | Comparison method; Intercept (Heyn) method; Microscopic examination | AS 1733 ASTM E112 | |||
Phase identification and proportion | Microscopic examination; Point count | ASTM E562 |
The only data displayed is that deemed relevant and necessary for the clear description of the activities and services covered by the scope of accreditation.
Grey text appearing in a SoA is additional freetext providing further refinement or information on the data in the preceding line entry.
Accreditation No.
218
Site No.
1086
Print date
03 Oct 2024